Agilent Technologies Agilent E5810A Uživatelský manuál Strana 75
- Strana / 164
- Tabulka s obsahem
- ŘEŠENÍ PROBLÉMŮ
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
Chapter 2 75
Installing the E5810
Installing and Configuring the Agilent IO Libraries Suite
Addressing
Instruments with
SICL
SICL addresses include the IP address or hostname of your E5810 as well
as the SICL address of the device on the E5810, and optionally the protocol
to be used. Some example addresses for SICL programs follow. These
examples assume that the SICL interface ID of your TCPIP interface is “lan”.
(You can specify this interface ID with the Connection Expert utility; “lan” is
the default SICL ID for the default TCPIP0 interface.)
lan[my_IP_Address]:gpib0,22
lan;vxi-11[my_IP_Address]:gpib0,22
lan[my_IP_Address]:COM1,488
lan;sicl-lan[my_IP_Address]:gpib0,11
NOTE
At the time of this writing, National Instruments I/O software does not
support the SICL-LAN protocol, but only the VXI-11 protocol. Because
RS-232 instruments are only supported by SICL-LAN and not VXI-11, you
cannot use National Instruments I/O software to program an RS-232
instrument on your E5810.
- Agilent E5810A 1
- User’s Guide 1
- Contents 3
- Contents 6 6
- Front Matter 7
- ICES Statement 9
- Safety Symbols 9
- WARNINGS 9
- Documentation History 10
- Copyright Information 11
- Trademark Information 11
- Support Information 11
- User’s Guide Information 12
- What’s in This 13
- Accessing an 13
- Electronic Copy of 13
- This Guide 13
- E5810 Related 14
- Documentation 14
- E5810 Description 15
- E5810 Hardware Description 17
- Local Network 18
- Connections 18
- Front Panel 19
- Display/LEDs 19
- Typical Power-On 20
- Sequence 20
- Preset Button 21
- 22 Chapter 1 22
- E5810 Software/Firmware 24
- E5810 Operating Features 25
- Client System 27
- Architecture 27
- How IO Application 28
- Software Works 28
- With the E5810 28
- E5810 IP Address 30
- Assignment 30
- Using E5810 Web 32
- Using a Supported 33
- Programming 33
- Language 33
- 34 Chapter 1 34
- Installing the E5810 35
- Installation Flowchart 37
- Before You Install the E5810 39
- Check System Requirements 40
- Getting Network Information 42
- Chapter 2 43 43
- What is a Local Network? 44
- Chapter 2 45 45
- E5810 Hub/Switch 46
- E5810 Crossover 47
- Cable Connections 47
- Apply Power to the 48
- Operation 49
- Configuring the 50
- E5810 for Enterprise 50
- Network Operation 50
- Click this icon 51
- Gateway 52
- Where to go Next 54
- Chapter 2 59 59
- Where to Go Next 60
- Open the Instrument Page 61
- Instrument Page Functions 62
- IO Libraries Suite 64
- Installing Agilent 65
- Start > Run 66
- Chapter 2 71 71
- Using Interactive IO 72
- Example: Using 72
- Interactive IO 72
- Programming Instruments 73
- Addressing 75
- Instruments with 75
- 76 Chapter 2 76
- Enter key 79
- Welcome page is the home 79
- Using the Welcome Page 80
- Navigation Bar 81
- E5810 Current Settings 82
- E5810 Support Information 83
- E5810 Documentation 84
- Viewing E5810 Configuration 85
- Modifying E5810 Configuration 86
- Chapter 3 87 87
- E5810 Configuration 88
- Parameter 88
- Descriptions 88
- Find and Control Instruments 96
- Connected to your E5810 96
- Finding Instruments 97
- Querying Instruments 98
- Other Web Access Functions 101
- Using Web Help 102
- Updating E5810 Firmware 103
- Agilent FTP site is 104
- Accessible From 104
- Guidelines 108
- Troubleshooting 108
- 110 Chapter 3 110
- Using E5810 Web Access 110
- Troubleshooting Information 111
- Checking the E5810 114
- Checking Front 115
- Panel Display Error 115
- Messages 115
- Checking E5810 Parameters 116
- Checking the Network 117
- Checking Web Browser Settings 118
- Cache and Page 119
- E5810 Operation 121
- SICL Timeout 122
- Set to 0 (infinite) 122
- How to Verify PC 123
- Client Connections 123
- Example: Using the 124
- Checking syslog Messages 125
- Message Description 126
- Example: Typical 127
- Runtime Error Messages 128
- Message Description/Actions 129
- Checking Instruments 131
- Checking RS-232 Instruments 132
- E5810 Specifications 133
- Information 135
- Operating Conditions 136
- Ordering Information 136
- Supplementary Information 136
- Supported Network Protocols 138
- Using the Telnet Utility 139
- Exiting the Telnet 142
- Typical Telnet 143
- Screen Display 143
- Telnet Commands for the E5810 144
- 146 Appendix B 146
- Glossary 147
- E Ethernet (MAC) Address 149
- F Friendly Name 149
- G gateway 150
- H Hostname 150
- I instrument 151
- N network protocols 153
- P proxy server 153
- R router 154
- S server 154
- U Universal Plug and Play 156
- VISA COM 157
- 158 Glossary 158
- 162 Index 162
- Agilent Technologies 164
Související produkty a manuály pro Brány / ovladače Agilent Technologies Agilent E5810A
(13 stránky)
(58 stránky)© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.059 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce