Agilent Technologies 222A Manuál s instrukcemi Strana 109
- Strana / 123
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
109
Specifications
Pulse Parameter Definitions
Jitter
Short-term instability of one edge relative to a reference edge. Usually
specified as rms value, which is one standard deviation or “sigma”. If
distribution is assumed Gaussian, six sigma represents 99.74% of the
peak-peak jitter.
The reference edge for period jitter is the previous leading edge. That for
delay jitter is the leading edge of the trigger output. Width jitter is the
stability of the trailing edge with regard to the leading edge.
Stability
Long-term average instability over a specific time, for example, hour,
year. Jitter is excluded.
Pulse Levels
Pulse output is specified as pulse top and pulse base (usually referred to
as high level and low level), or as peak to peak amplitude and median
offset. A “window” specification shows the limits within which the pulse
can be positioned.
Window
Max
High
Level
Min
Low
Level
Amplitude
Zero Volts
Median
Offset
High Level
Low Level
- Reference Guide 1
- Agilent 81101A 50 MHz 3
- Pulse Generator 3
- Copyright 4
- Warranty 4
- Limitation of Warranty 5
- Exclusive Remedies 5
- Certification 5
- Services and Support 5
- Safety Summary 6
- Ground the Instrument 7
- Safety Symbols 8
- About this Book 9
- Conventions Used in this Book 10
- Contents 11
- 1General Programming 13
- The GP-IB Interface Bus 14
- Agilent 81101A Remote Control 15
- Programming Recommendations 16
- Common Command Summary 18
- Status Model 19
- Condition Register 20
- Transition Filters 20
- Event Register 20
- Enable Register 21
- Status Byte 22
- Standard Event Status Group 22
- OPERation Status Group 23
- QUEStionable Status Group 24
- 2Programming Reference 25
- Agilent 81101A SCPI Command 26
- Programming Reference 31
- Programming the Instrument 35
- Continuous 36
- Triggered 36
- External Width 37
- SCPI Instrument Command List 38
- :DISPlay[:WINDow][:STATe] 43
- DISP OFF 43
- :MMEMory:CATalog? 44
- :MMEMory:CDIRectory 44
- :MMEMory:COPY 45
- :MMEMory:DELete 45
- :MMEMory:INITialize 45
- :MMEMory:LOAD:STATe 46
- :MMEMory:STORe:STATe 46
- :OUTPut[1][:NORMal][:STATe] 47
- :OUTP ON 47
- :OUTPut[1]:IMPedance:EXTernal 47
- :OUTPut[1]:POLarity 48
- Amplitude = High – Low 50
- Offset = 50
- High – Low 50
- Period = 54
- Frequency 54
- [:SOURce]:HOLD 55
- [:SOURce]:PHASe[1][:ADJust] 56
- [:SOURce]:PULSe:DCYCle[1] 57
- [:SOURce]:PULSe:DELay[1] 57
- [:SOURce]:PULSe:DELay[1]:HOLD 58
- [:SOURce]:PULSe:DELay[1]:UNIT 59
- DblDel% = 60
- Frequency = 62
- [:SOURce]:PULSe:PERiod:AUTO 63
- [:SOURce]:PULSe:TDELay[1] 63
- [:AMPlitude] 67
- [:SOURce]:PULSe:WIDTh[1] 68
- [:SOURce]:ROSCillator:SOURce 68
- Amplitude 70
- Offset = 72
- High–Low 73
- :STATus:PRESet 76
- :SYSTem:CHECk[:ALL][:STATe] 78
- :SYSTem:ERRor? 78
- :SYSTem:KEY 79
- :SYSTem:PRESet 81
- :SYSTem:SECurity[:STATe] 82
- :SYSTem:SET 83
- :SYSTem:VERSion? 83
- :SYSTem:WARNing[:COUNt]? 83
- :SYSTem:WARNing:STRing? 84
- :SYSTem:WARNing:BUFFer? 84
- :TRIGger[:SEQuence[1]]:COUNt 84
- :TRIGger:IMPedance 85
- :TRIGger:LEVel 86
- :TRIGger:SLOPe 86
- 3Specifications 89
- Manufacturer 90
- Supplementary 90
- Information 90
- Agilent 81101A Specifications 91
- Recalibration period 92
- Acoustic Noise Emission 92
- Timing Specifications 93
- Transition Times 95
- Level Specifications 96
- Clock Sources 97
- Clock / PLL Reference Input 98
- Phase Locked Loop (PLL) 98
- Output Modes 99
- Trigger Modes 100
- Trigger Output 101
- Strobe Output 101
- Typical Delays 102
- Human Interface 103
- Remote Control 104
- Pulse Parameter Definitions 105
- Time Reference Point 106
- Pulse Period 106
- Trigger Delay 106
- Pulse Width 106
- Pulse Delay 107
- Double Pulse Delay 107
- Interchannel Delay (Skew) 107
- Transition Time 108
- Linearity 108
- Stability 109
- Pulse Levels 109
- Preshoot, Overshoot, Ringing 110
- Settling Time 110
- Repeatability 111
- Specifications 112
- Front Panel Controls 117
- Edition E0300 118
- Printed in Germany 118
- 81101-91021 118
- DECLARATION OF CONFORMITY 123
Související produkty a manuály pro Měření, testování a kontrola Agilent Technologies 222A
(24 stránky)
(18 stránky)© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.061 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce