Agilent Technologies X/P/K281C Uživatelský manuál stáhnout pdf (Strana 12)

□ Vector- and scalar-calibrated converter measurements

(Option 083)

This converter measurement is a superset and includes not

only the scalar-calibrated converter measurement, but

also the vector-mixer calibration (VMC). The advanced and

unique VMC delivers exceptional conversion loss amplitude

and phase accuracy for mixer and converter measurements.

This application provides an intuitive and easy-to-use user

interface for setting up mixer and converter measurements,

with single or dual conversion stages (up to two LO’s), along

with control of up to two external signal generators for use as

LO.External synthesizers supported include the Agilent ESG

series and the PSG series of signal source families as well as

other SCPI controlled signal generators. Option 083 requires

Option 080, and cannot be ordered with Option 082.

□ Embedded LO measurements (Option 084)

Advanced software tuning that provides absolute group delay of

converters with embedded LOs without the need for access to a

common reference signal. The measurement result is the same

as locking the DUT LO to the reference mixer LO. (Option 080

and 083 required) Requires firmware A.07.50 and above.

□ Gain compression application (Option 086)

The Gain Compression Application (GCA) provides input power,

output power, gain, and phase at an amplifier's compression

point, over a specified frequency and power range. GCA's

SMART Sweep is very fast and easy-to-use. GCA also includes

a guided calibration that corrects for absolute power levels,

frequency response, and mismatch errors. Requires firmware

A.08.00 and above

□ N-port capabilities (Option 551)

Adds full N-port error correction and measurement capabilities

to the PNA-X network analyzer. External test set is required.

□ High-power test set (Option H85)

With the standard test set conﬁ gurations that include source

attenuators, the internal bias tees limit the maximum test port

power to +30 dBm. Option H85 removes the bias tees

between the source attenuators and the test port couplers.

This extends the maximum port power that the analyzer can

safely handle to +43 dBm. Option H85 requires Option 080,

plus Option 224 or 423.

□ Rack mount kit without handles (Option 1CM)

Adds a rack mount (5063-9217) and rail kit (E3663AC) for use

without handles.

1. When configured as a multiport analyzer with Option 551, the

combiner feature of Option 224 or 423 is not available. When configured

as a standalone analyzer, the combiner feature is available.

□ Pulse I/O adapter (N1966A)

An adapter for connecting between the Pulse I/O connector on

the rear panel of the PNA-X and the coaxial inputs and outputs

of external pulse generators and external pulse modulators.

Coaxial connectors are SMB-male. (See diagram below for

details of the Pulse I/O adapter.

The PULSE IN connectors are for controlling the PNA-X's internal

IF gates, which are enabled with Option H08 and used with

narrowband detection. The PULSE OUT connectors are from the

PNA-X's four internal pulse generators, which are enabled with

Option 025. The PULSE SYNC IN connector is used to synchronize

the internal pulse generators with an external timing pulse. The

RF PULSE MOD IN connector controls the internal pulse modulator(s)

which are enabled with Options 021 and 022.

Pulse I/O adapter (N1966A) simplifies connections

PNA-X Network Analyzer

1 2 ... 7 8 9 10 11 12 13 14 15 16 17 ... 37 38

Komentáře k této Příručce

Žádné komentáře

Agilent Technologies X/P/K281C Uživatelský manuál Strana 12

Komentáře k této Příručce

Související produkty a manuály pro Multimetry Agilent Technologies X/P/K281C