Agilent Technologies Agilent E5250A Uživatelská příručka Strana 116
- Strana / 182
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
3-22 Agilent 4155C/4156C VXIplug&play Driver User’s Guide, Edition 1
Programming Examples Using Agilent VEE
Staircase Sweep Measurements
Staircase Sweep Measurements
To make staircase sweep measurements, use the following functions.
Table 3-6 Functions for Staircase Sweep Measurements
A program example is shown in Figure 3-18 on page 3-23. This program measures
MOSFET Id-Vd characteristics. The measurement setup is shown in Figure 3-17.
Figure 3-17 Device Connection and Source Setup for Example Program
Description Function Parameters
Output Switch Setup hp4156b_setSwitch channel,state
Output Filter Setup hp4156b_setFilter channel,state
Integration Time Setup hp4156b_setInteg table,time,average
Forces dc bias hp4156b_force channel,mode,range,value,compliance,polarity
Sweep Source Setup hp4156b_setIv channel,mode,range,start,stop,point,hold,delay,
s_delay,comp,p_comp
Executes measurement hp4156b_sweepIv channel,mode,range,point,source[ ],value[ ],
status[ ]
Disables output hp4156b_zeroOutput channel
A
Drain
Substrate
Gate
Source
channel: SMU2
mode: V output
range: 20V
start: VdStart
stop: VdStop
point: MeasPoint
hold: 0sec
delay: 0sec
s_delay: 0sec
comp: 0.1A
p_comp: 0.5W
channel: SMU4
mode: V output
value: Vsub
range: 2V
comp: 0.1A
polarity: AUTO
channel: SMU3
mode: V output
value: Vg
range: 20V
comp: 10mA
polarity: AUTO
channel: SMU1
mode: V output
value: Vs
range: 2V
comp: 0.1A
polarity: AUTO
channel: SMU2
mode: I measure
range: 0.1A
point: MeasPoint
source: Vd
value: Id
status: status
- Agilent Part No. 04156-90080 1
- Printed in Japan January 2001 1
- Edition 1 1
- Legal Notice 2
- In This Manual 5
- Contents 10
- 1 Installation 13
- Software Requirements 15
- Installing 4155/4156 Driver 17
- To Install the Driver 19
- 2 Driver Functions 21
- Sets the zero offset cancel 23
- 3 Programming Examples Using 95
- Programming Basics 97
- To display the To/From object 101
- To set input parameters 103
- 104
- To use input variables 105
- Debugging Your Program 108
- To check for instrument error 109
- High-Speed Spot Measurements 111
- Collector 113
- Staircase Sweep Measurements 116
- Substrate 118
- Pulsed Spot Measurements 124
- Pulsed Sweep Measurements 128
- Sampling Measurements 135
- Stress Force 139
- Agilent VEE 141
- Introduction 143
- What are Sample Programs? 144
- Definition of Vth 145
- Execution Mode 146
- Measurement Data Files 148
- Installation 149
- Working Directory 150
- Subdirectory 150
- Using sample1.vee 151
- Program Execution Flow 152
- Panel Display 154
- To Execute sample1.vee 155
- Using sample2.vee 159
- To Execute sample2.vee 163
- Customizing Sample Programs 167
- To Change an GPIB Address 168
- To Remove a Test Device 170
- 171
- 171
- 171
- To Remove a Source Output 172
- 173
- 173
- To Add a Test Device 174
- 176
- To Save Measurement Data 181
Související produkty a manuály pro Síťové přepínače Agilent Technologies Agilent E5250A
(36 stránky)
(28 stránky)Case-mate Non manuels d'utilisation
La liste de Case-mate Non produits contient 1 manuels d'utilisation pour les modèles 1. Tous les guides d'utilisation en format pdf peuvent être téléchargés ou consultés en ligne.
Komentáře k této Příručce