Agilent Technologies SMPTE 310M Uživatelský manuál

SMPTE 310M InterfaceInstallation GuideProduct Number: E6292ADocument Part Number: E6292-94000 Ed2ãCopyright Hewlett-Packard Company 1999, 2000

Introduction2For more help... If you have any questions about the installation procedure, call your local HP representative. You can also contact digi

3MPEGscope Plus and MPEGscope LiteMPEGscope Plus and MPEGscope LiteThis section explains how to install the SMPTE 310M interface into the MPEGscope Pl

MPEGscope Plus and MPEGscope Lite4Step 1: Remove the cover WA RN I N G Never remove the computer cover without first removing the power cord from the

5MPEGscope Plus and MPEGscope Lite6Grasp the cover on the sides at the back of the computer and slide it forwards and off the computer.5Flip the two l

MPEGscope Plus and MPEGscope Lite6Step 2: Remove optional interfaceComplete this step if your MPEGscope already has an optional interface installed an

7MPEGscope Plus and MPEGscope Lite3If your MPEGscope has a Real-time Analyzer, disconnect the ribbon cable from the Real-time Analyzer card. The cable

MPEGscope Plus and MPEGscope Lite8Step 3: Install SMPTE interface1Attach the antistatic wrist strap to your wrist and to the PC chassis as described i

9MPEGscope Plus and MPEGscope LiteAlternative configurationThis configuration applies only if your MPEGscope is housed in a Kayak XU PC (e.g., E6277B

MPEGscope Plus and MPEGscope Lite10Step 4: Replace the cover1Ensure that the two latches on the front sides of the cover are lifted up.3Lower the two

11MPEGscope Plus and MPEGscope LiteMPEGscope Plus with SMPTE 310M interface installedSMPTE 310M interface installed in slot 3.

The information contained in this document is subject to change without notice.HEWLETT-PACKARD MAKES NO WARRANTY OF ANY KIND WITH REGARD TO THIS MATER

MPEGscope Portable and Portable Lite12MPEGscope Portable and Portable LiteThis section explains how to install the SMPTE 310M interface into the MPEGs

13MPEGscope Portable and Portable LiteStep 1: Remove the cover WA RN I N G Never remove the computer cover without first removing the power cord from

MPEGscope Portable and Portable Lite146Remove the six back panel screws from the back and side, then lift off the back panel.5Carefully lay MPEGscope

15MPEGscope Portable and Portable LiteStep 2: Remove optional interfaceComplete this step if your MPEGscope already has an optional interface installe

MPEGscope Portable and Portable Lite16Step 3: Install SMPTE interface1Attach the antistatic wrist strap to your wrist and to the PC chassis as describ

3If your MPEGscope has a Real-time Analyzer, reconnect the ribbon cable from the MPEGscope main card to the Real-time Analyzer card.

MPEGscope Portable and Portable Lite18Step 4: Replace the cover4Reconnect your display, power cables, and LAN connection, then power on your MPEGscope

19MPEGscope Portable and Portable LiteE6300A MPEGscope Portable with SMPTE 310M interface installedSMPTE 310M interface installed in slot 2.

Connecting to the SMPTE 310M interface20Connecting to the SMPTE 310M interfaceDVB–SPI IN/OUTSMPTE 310ME6292AINOUT5Connect the input line from your sys

21Configuring the softwareConfiguring the softwareBecause the SMPTE 310M interface receives and transmits data via the MPEGscope SPI interface, you do

iCertificationAgilent Technologies certifies that this product met its published specifications at the time of shipment from the factory. Agilent Tech

Configuring the software224Select the mode to use for your test.3Select the Mode tab.2Select Configure.For information about modes, press the Help but

23Configuring the software5Select the Rx tab.6Select receiver options.7Select the Tx tab.8Select transmitter options.For information about receiver an

SMPTE 310M interface specificationsWA RN I N G To ensure the Electromagnetic Compatibility (EMC) of MPEGscope, use shielded cables on all interfaces.

25Release NotesRelease NotesThis section describes two SMPTE 310M interface constraints that may affect your test. It includes a description of the pr

iiDieses Zeichen steht für ein Produkt der Gruppe 1, Klasse A, für den Einsatz im industriuellen, wissenschaftlichen und medizinischen Bereich.This pr

iii Borne de mise à la terre de cadre ou de châssis. Connectée en principe au cadre métallique de l’équipement. Courant alternatif (ca).Courant contin

page inner marginhanging column right marginbody text left marginbody text bottom marginfooter rulling linefooter text base lineouter margin for text

1IntroductionIntroductionThe E6292A SMPTE (Society of Motion Picture and Television Engineers) 310M interface is serial-to-parallel converter that rec