Agilent Technologies 83480A Uživatelský manuál

Agilent 83480A DigitalCommunications AnalyzerAgilent 54750A Digitizing OscilloscopeQuick Start Guide

1-2Introducing the InstrumentThe Agilent 83480A, Agilent 54750A—At a GlanceThe Agilent 83480A, Agilent 54750A—At a GlanceThe Agilent 83480A-series dig

1-3Introducing the InstrumentThe Agilent 83480A, Agilent 54750A—At a GlanceCertificationAgilent Technologies certifies that this product met its publi

1-4Introducing the InstrumentA Quick Tour of the Front PanelA Quick Tour of the Front PanelThis section describes how to use the front panel. This inf

1-5Introducing the InstrumentA Quick Tour of the Front PanelHardkeysThe two types of hardkeys are instant action and menu. Clear display and Run are e

1-6Introducing the InstrumentA Quick Tour of the Front Panel Figure 1-2. The instrument display SoftkeysThe softkeys are to the right of the display,

1-7Introducing the InstrumentA Quick Tour of the Front PanelThe highlighted choice is the selection that is currently active. In Figure 1-3, triggered

1-8Introducing the InstrumentA Quick Tour of the Front Panel Figure 1-4. Menu softkey selection Continuous softkeysA typical example of the continuous

1-9Introducing the InstrumentA Quick Tour of the Front PanelBecause the Trigger menu only has one of this type of softkey, it is active when the menu

1-10Introducing the InstrumentA Quick Tour of the Front PanelYou change selections by pressing the Hysteresis softkey, which brings up a sec-ond level

2Equipment Used in These Exercises 2-3Exercise 1. Installing a Plug-in Module 2-4Exercise 2. Turning On the Instrument 2-5Exercise 3. Connecting a Sig

ii© Copyright Agilent Technologies 2000All Rights Reserved. Repro-duction, adaptation, or trans-lation without prior written permission is prohibited,

2-2Operating the InstrumentOperating the InstrumentOperating the InstrumentThis chapter contains several exercises that will familiarize you with the

2-3Operating the InstrumentEquipment Used in These ExercisesEquipment Used in These ExercisesAll of the pictures of the display in this book were gene

2-4Operating the InstrumentExercise 1. Installing a Plug-in ModuleExercise 1. Installing a Plug-in ModuleThe purpose of a plug-in module is to provide

2-5Operating the InstrumentExercise 2. Turning On the InstrumentExercise 2. Turning On the Instrument1Set the line-voltage switch on the rear panel to

2-6Operating the InstrumentExercise 3. Connecting a SignalExercise 3. Connecting a SignalCAUTIONElectrostatic discharge (ESD) on or near input connect

2-7Operating the InstrumentExercise 4. Finding the SignalExercise 4. Finding the SignalThe purpose of this exercise is to demonstrate the Autoscale fu

2-8Operating the InstrumentExercise 5. Modifying the SetupExercise 5. Modifying the SetupThe purpose of this exercise is to show you the Channel and T

2-9Operating the InstrumentExercise 5. Modifying the SetupUsing the keypad When using the Agilent 83483A, 54751A electrical plug-in module, the knob o

2-10Operating the InstrumentExercise 5. Modifying the Setup Figure 2-2. Signal vertical displayChanging the time base 5To display the Time Base menu a

2-11Operating the InstrumentExercise 5. Modifying the SetupUsing the keypad 6When the knob and arrow keys are not in the Fine mode, they operate in a

iiiWhat You’ll Find in This BookWhat You’ll Find in This BookThis book gives you a quick introduction to the instrument. It is not intended as a compr

2-12Operating the InstrumentExercise 5. Modifying the SetupSetting the reference 8To set the reference to the left or center of the graticule area, pr

2-13Operating the InstrumentExercise 6. Making Measurements on the SignalExercise 6. Making Measurements on the SignalThe purpose of this exercise is

2-14Operating the InstrumentExercise 6. Making Measurements on the SignalPositioning the markers4To position the X1 marker, press: X1 Position Set the

2-15Operating the InstrumentExercise 6. Making Measurements on the SignalNotice the ∆X and ∆Y at the bottom of the display. The ∆X value is the width

2-16Operating the InstrumentExercise 6. Making Measurements on the Signal Figure 2-5. Signal automatic measurementsDisplaying the scale and offset val

2-17Operating the InstrumentExercise 7. Using the Help MenuExercise 7. Using the Help MenuTo display the Help menu, press Help. A screen similar to Fi

3If the Mainframe Does Not Operate 3-3If the Plug-in Does Not Operate 3-4In Case of Difficulty

3-2In Case of DifficultyIn Case of DifficultyIn Case of DifficultyThis chapter provides suggestions for you to follow if the mainframe or plug-in modu

3-3In Case of DifficultyIf the Mainframe Does Not OperateIf the Mainframe Does Not Operate If the mainframe does not operate, check the following: 1Is

ivGeneral Safety ConsiderationsGeneral Safety ConsiderationsThis product has been designed and tested in accordance with IEC Publica-tion 61010-1, Saf

3-4In Case of DifficultyIf the Plug-in Does Not OperateIf the Plug-in Does Not Operate If the plug-in does not operate:1Make the following checks: • I

3-5In Case of DifficultyIf the Plug-in Does Not OperateAfter viewing the signal, press triggered. • Make sure Channel Display is on by pressing: Chann

IndexIndex-1Symbols+width key, 2-15Aamplitude, 2-7measurement, 2-14scale, 2-10analog signal, 2-4automatic measurement, 2-13, 2-15Autoscale key, 2-7, 3

Index-2IndexMmanual marker measurements, 2-15manual softkey, 2-13Marker key, 2-13measuring the signal, 2-13menudisplay, 1-6key, 1-5softkeys, 1-7messag

Index-3IndexX1/X2 Position softkeys, 2-14X2, Y2 Source softkey, 2-13YY1/Y2 Position softkeys, 2-14

vGeneral Safety ConsiderationsCAUTIONBefore this instrument is switched on, make sure its primary power circuitry has been adapted to the voltage of t

ContentsContents-1General Safety Considerations iiv1 Introducing the InstrumentThe Agilent 83480A, Agilent 54750A—At a Glance 1-2A Quick Tour of the F

1Entry devices 1-4Disk drive 1-4CAL signal 1-4Hardkeys 1-5Display 1-5Softkeys 1-6Introducing the Instrument