Agilent Technologies AGILENT U2761A Uživatelská příručka Strana 108
- Strana / 123
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
90 U2761A User’s Guide
2 Features and Functions
Set Triggering Using SCPI Commands
Example 1
-> *CLS; *RST //To reset the U2761A to
default power-on state,
this command can be
ignored if this operation
is not required.
-> FUNC SIN //Sets the carrier waveform
to Sine wave.
-> VOLT 5 VPP //Sets the output amplitude
to 5 Vpp.
-> VOLT:OFFS 0 //Sets the output offset to
0.
-> SWE:STAT ON //Enables frequency sweep.
-> FREQ:STAR 500 //Changes the start
frequency to 500 Hz.
-> FREQ:STOP 10000 //Changes the stop
frequency to 10 kHz.
-> SWE:SPAC LIN //Changes the sweep mode
to Linear.
-> SWE:TIME 2 //Changes the sweep time
to 2 s.
-> TRIG:SOUR IMM //Changes the sweep trigger
source to Internal.
-> OUTP:TRIG ON //Turns on the trigger
output.
-> OUTP:TRIG:SLOP POS //Outputs the trigger on a
rising edge.
-> OUTP ON //Turns on output.
- Agilent U2761A 1
- USB Modular 1
- Function/Arbitrary 1
- Waveform Generator 1
- Safety Symbols 3
- General Safety Information 4
- Environment Conditions 5
- Regulatory Markings 6
- 2002/96/EC 7
- Declaration of Conformity 8
- Additional Information: 9
- Performance Criteria: 9
- In This Guide… 10
- Contents 11
- XII U2761A User's Guide 12
- U2761A User's Guide XIII 13
- XIV U2761A User's Guide 14
- List of Figures 15
- Figure 2-31 Ramp waveform 91 16
- List of Tables 17
- XVIII U2761A User’s Guide 18
- Getting Started 19
- Introduction 20
- Product at a Glance 21
- Front View 22
- Rear View 22
- Product Dimensions 23
- Dimensions With Bumpers 24
- Standard Purchase Items 25
- Inspection and Maintenance 26
- Installation 27
- A. Check Your System 28
- C. Install the Module Driver 30
- Chassis Installation 42
- Features and Functions 43
- Output Configuration 44
- Function Limitation 45
- Amplitude Limitation 45
- Output Frequency 47
- Function Limitations 48
- Duty Cycle Limitations 48
- Output Amplitude 49
- Limits Due to Units Selection 50
- DC Offset Voltage 51
- Output Units 53
- Output Termination 54
- Duty Cycle (Square Waves) 56
- Symmetry (Ramp Wave) 58
- Output Control 59
- Pulse Waveform 63
- Pulse Width 64
- Pulse Duty Cycle 65
- Amplitude Modulation (AM) 67
- Carrier Waveform 68
- Carrier Frequency 69
- Modulating Waveform 70
- Modulating Waveform Frequency 71
- Modulation Depth 71
- Frequency Modulation (FM) 73
- Frequency Deviation 77
- Phase Modulation (PM) 79
- Phase Deviation 83
- To Select FSK Modulation 84
- FSK Carrier Frequency 86
- FSK “Hop” Frequency 87
- FSK Rate 88
- To Select PSK Modulation 89
- PSK Carrier Frequency 91
- PSK Rate 92
- PSK Deviation 92
- To Select ASK Modulation 94
- ASK Rate 97
- Frequency Sweep 98
- Sweep Mode 100
- Sweep Time 100
- Sweep Trigger Source 101
- Remote Interface Operation 102
- Triggering 103
- Internal Triggering 104
- Manual Triggering 104
- External Triggering 105
- Trigger Input Signal 106
- Trigger Output Signal 106
- Soft Front Panel Operation 107
- Arbitrary Waveforms 109
- Agilent Technologies 113
- Product Characteristics 114
- WAVEFORMS 115
- WAVEFORM CHARACTERISTICS 115
- Ramp, Triangle 116
- Arbitrary 116
- Range +360° to –360° 117
- SWEEP CHARACTERISTICS 119
- TRIGGER CHARACTERISTICS 119
- Trigger input 119
- Trigger output 119
- 102 U2761A User’s Guide 120
- U2761A User’s Guide 103 121
- 104 U2761A User’s Guide 122
Související produkty a manuály pro ne Agilent Technologies AGILENT U2761A
(66 stránky)Case-mate Non manuels d'utilisation
La liste de Case-mate Non produits contient 1 manuels d'utilisation pour les modèles 1. Tous les guides d'utilisation en format pdf peuvent être téléchargés ou consultés en ligne.
Komentáře k této Příručce