Agilent Technologies 22D Uživatelská příručka Strana 55
- Strana / 66
- Tabulka s obsahem
- ŘEŠENÍ PROBLÉMŮ
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
User’s and Service Guide 47
87050A Option K24 Assembly Replacement and Post-Repair Procedures
Connector Replacement
The 50 Ω, 3.5 mm connectors are available separately as (5062-6618). It is possible to
replace them in the field. An alternative to replacing a damaged connector would be to
replace just the center pin components. The components for the assembly are:
When replacing just the pin and bead, a liquid thread-locking adhesive such as part
number 0470-1590 will be needed. Re-use any shims and spacers from the connector being
replaced. For best results, use a connector gauge to verify pin depth. See Figure 4 on
page 10 for proper pin-depth. Add or subtract spacers as required. Spacers and shims are
also available from Agilent Technologies.
WARNING The opening of covers or removal of parts is likely to expose the user to
dangerous voltages. Disconnect the instrument from all voltage sources
while it is being opened.
Component Part Number
3.5 mm Connector, RF (complete) 5062-6618
3.5 mm Pin and Bead Assembly (only) 5061-5394
- Agilent Technologies 1
- 87050A Option K24 1
- Warranty Statement 4
- Safety Notes 5
- Definitions 5
- Contents 7
- Description 10
- Verifying the Shipment 11
- General Specifications 12
- Power Requirements 13
- Environmental Requirements 14
- 8 User’s and Service Guide 16
- Front and Rear Panel Features 17
- Ground Connector 18
- Port Connection Status LCD 18
- Printer/Test Set Switch 19
- GPIB Connector 19
- Address Switch 20
- Line Module 20
- Available Fuse 20
- Power Cables 21
- 14 User’s and Service Guide 22
- System Setup 23
- 16 User’s and Service Guide 24
- Performance Verification 25
- Operation 26
- Table 4 Test Port Addresses 28
- 22 User’s and Service Guide 30
- 87050A Option K24 Operation 30
- Table 5 Switch Count Commands 31
- Calibrating the Test System 33
- Making Measurements 34
- User’s and Service Guide 27 35
- Theory of Operation 36
- User’s and Service Guide 29 37
- Performance Tests 38
- Return Loss 39
- Isolation 39
- Performance Test Record 40
- User’s and Service Guide 33 41
- 34 User’s and Service Guide 42
- Table 8 Insertion Loss Record 43
- 36 User’s and Service Guide 44
- User’s and Service Guide 37 45
- 38 User’s and Service Guide 46
- User’s and Service Guide 39 47
- Table 13 Return Loss Record 48
- User’s and Service Guide 41 49
- 42 User’s and Service Guide 50
- User’s and Service Guide 43 51
- 44 User’s and Service Guide 52
- User’s and Service Guide 45 53
- 46 User’s and Service Guide 54
- Connector Replacement 55
- General Troubleshooting Notes 56
- User’s and Service Guide 49 57
- 50 User’s and Service Guide 58
- Introduction 59
- Before Applying Power 59
- Connector Care and Cleaning 59
- Declaration of Conformity 59
- Statement of Compliance 59
- General Safety Considerations 60
- Regulatory Information 62
- 56 User’s and Service Guide 64
- Service and Support Options 65
- Contacting Agilent 65
- 58 User’s and Service Guide 66
Související produkty a manuály pro Měření, testování a kontrola Agilent Technologies 22D
(66 stránky)Case-mate Non manuels d'utilisation
La liste de Case-mate Non produits contient 1 manuels d'utilisation pour les modèles 1. Tous les guides d'utilisation en format pdf peuvent être téléchargés ou consultés en ligne.
Komentáře k této Příručce