Agilent Technologies 81134A Servisní příručka stáhnout pdf (Strana 34)

SCPI Commands Reference DIGital Commands

34 Agilent 81133A/81134A Pulse Generator Programming Guide, March 2007

:DIGital[1|2][:STIMulus]:SIGNal:

CROSsover:[STATe]

Syntax

:DIG[1|2][:STIM]:SIGN:CROS:STAT[?]

Form Set & Query

Description For each channel, the crossover mode of the NRZ signal in PRBS

or data pattern mode can be enabled. This is used to artificially

close the eye pattern, simulating distortion.

If you enabled the variable crossover mode, specify the variable

crossover point with

“:DIGital[1|2][:STIMulus]:SIGNal:

CROSsover:[VALue]” on page 32.

Parameter ON|OFF|1|0

*RST value OFF|0

Example Enable the variable crossover mode.

:DIG:SIGN:CROS:STAT ON

1 2 ... 29 30 31 32 33 34 35 36 37 38 39 ... 103 104

Programming Guide 1
Important Notice 2
About This Programming Guide 3
Contents 5
OUTPut Commands 39 6
SOURce Commands 45 6
Status Handling Commands 67 6
Troubleshooting 97 7
Introduction 10
SCPI Commands Reference 17
Common Commands 19
Standard Settings 21
DIAGnostic Commands 23
:CAL:TIM 24
DIGital Commands 25
Range Maximum Pattern Length 29
60 – 3360 Mhz 12 Mbit 29
30 – 60 Mhz 6 Mbit 29
15 – 30 Mhz 3 Mbit 29
CROSsover:[VALue] 32
CROSsover:[STATe] 34
DISPlay Commands 35
MEASure Commands 36
:MEASure:FREQuency? 37
:MEASure:PERiod? 38
OUTPut Commands 39
:OUTPut[0 41
:OUTPut0:SOURce 42
:OUTPut[0 43
:OUTPut[1 43
:OUTPut[1 44
:OUTPut:CENTral 44
SOURce Commands 45
[:SOURce]:FUNCtion[:SHAPe] 50
[:SOURce]:FUNCtion:MODe[1 51
[:SOURce]:PHASe[:ADJ][1 53
[:SOURce][:PULSe]:DCYCle[1 54
[:SOURce][:PULSe]:DELay[1 55
[:SOURce][:PULSe]:DESKew[1 56
[:SOURce][:PULSe]:DHOLd[1 56
[:SOURce][:PULSe]:PERiod 57
[:SOURce][:PULSe]:WIDTh[1 58
[:SOURce]:PM[1 59
[:SOURce]:PM[1 59
[:IMMediate][:AMPLitude] 60
[:IMMediate]:OFFSet 61
[:IMMediate]:HIGH 62
[:IMMediate]:LOW 63
[:IMMediate]:TERM 64
[:SOURce]:VOLTage[1 64
[:AMPLitude]? 64
Status Handling Commands 67
:STATus:OPERation 70
:STATus:PRESet 70
:STATus:QUEStionable 71
:STATus:QUEStionable:VOLTage 73
:STATus:QUEStionable:MONotony 76
SYSTem Commands 79
:SYSTem:ERRor? 81
:SYSTem:PRESet 81
:SYSTem:SET 82
:SYSTem:VERSion? 82
:ADDRess 84
:DGATeway 85
TRIGger Commands 86
:TRIGger:SOURce 87
:TRIGger:TERM 88
:TRIGger:TERM:STATE[?] 89
ARM Commands 90
:ARM[:SEQuence][:LAYer]:LEVel 91
:ARM[:SEQuence][:LAYer]:SLOPe 92
:ARM[:SEQuence][:LAYer]:TERM 94
:ARM[:SEQuence][:LAYer]:STOP 95
Troubleshooting 100
5988-7402EN 104

Komentáře k této Příručce

Žádné komentáře

Agilent Technologies 81134A Servisní příručka Strana 34

Komentáře k této Příručce

Související produkty a manuály pro Měření, testování a kontrola Agilent Technologies 81134A