Agilent Technologies Weather Radio 1680 Uživatelský manuál Strana 33
- Strana / 174
- Tabulka s obsahem
- ŘEŠENÍ PROBLÉMŮ
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
33
Chapter 3: Testing Performance
To set up the logic analyzer for the state mode tests
To set up the logic analyzer for the state mode tests
1 Set up the logic analyzer:
a If you have not already done so, do the procedure “To set up the test
equipment and the logic analyzer” on page 23.
b Exit and restart the Agilent Logic Analyzer application to reinitialize
the logic analyzer.
2 Configure the Analyzer Setup dialog:
a Click the Sampling Setup icon.
b Select State - Synchronous Sampling.
c Configure Trigger Position - 100% poststore.
d Select an Acquisition Depth of 8K.
e Click the Buses/Signals tab.
f Click the threshold field of one of the pods. The Threshold Settings
dialog appears.
g In the Threshold Settings dialog, select Standard and ECL (–1.30 V).
h Click OK to close the Threshold Settings dialog.
i Click OK to close the the Analyzer Setup dialog.
- Logic Analyzer 1
- Features 2
- Service Strategy 3
- In This Book 4
- Contents 5
- Accessories 10
- Specifications 11
- Characteristics 11
- Auxiliary Power 12
- Dimensions 13
- Recommended Test Equipment 14
- Preparing for Use 15
- Power Requirements 16
- Operating Environment 16
- To inspect the logic analyzer 16
- To apply power 17
- To start the user interface 18
- To clean the logic analyzer 18
- To test the logic analyzer 18
- Testing Performance 19
- The Logic Analyzer Interface 20
- Test Strategy 20
- Test Interval 20
- Performance Test Record 20
- Test Equipment 20
- To make the test connectors 21
- Set up the test equipment 23
- Chapter 8 24
- 3 Set the reporting level 26
- 5 Click Start 26
- Set up the equipment 28
- Test the ECL Threshold 30
- Test the 0 V User Threshold 31
- Test the next pod 32
- “from” field 36
- Verify the test signal 40
- Calibrating and Adjusting 75
- Logic analyzer calibration 76
- Troubleshooting 77
- To install the fan guard 78
- To use the flowcharts 79
- To check the power-up tests 87
- 01680f01.cdr 89
- To test disk drive voltages 90
- To verify the CD-ROM 92
- To verify connectivity 99
- Device Manager 100
- 2 Shut down the instrument 100
- Chapter 5: Troubleshooting 102
- General Troubleshooting 103
- 6 Set the reporting level 104
- 8 Click Start 104
- Acquisition board status LEDs 106
- To test the auxiliary power 112
- Replacing Assemblies 113
- To remove the power supply 117
- To remove the hard disk drive 118
- Apply the tape as shown 121
- To remove the PCI boards 122
- To remove the motherboard 123
- To remove the inverter board 130
- To remove the fans 131
- To remove the cable tray 132
- To remove the fascia 134
- To remove the deck 137
- To remove the line filter 140
- Replaceable Parts 143
- Replaceable Parts Ordering 144
- Replaceable Parts List 145
- Exploded View 146
- Exchange Assemblies 147
- Replacement Parts 147
- Front Panel Assembly 151
- Chapter 7: Replaceable Parts 157
- Theory of Operation 159
- Block-Level Theory 160
- Power Supply 162
- Acquisition Board 162
- Power Distribution Board 165
- Front Panel Board 165
- Self-Tests Descriptions 167
- Acquisition Board Self Tests 168
- Logic Analyzer Self-Tests 169
- Trademark 173
- Acknowledgements 173
Související produkty a manuály pro Komponenty podvozku Agilent Technologies Weather Radio 1680
(12 stránky)MotoChello manuales
La lista de dispositivos de MotoChello contiene 1 manuales de usuario y guías para 1 modelos en 2 tipo de dispositivos
Komentáře k této Příručce