Agilent Technologies Agilent E5810A Uživatelská příručka Strana 90
- Strana / 159
- Tabulka s obsahem
- ŘEŠENÍ PROBLÉMŮ
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
90 Chapter 3
Using E5810A Web Access
Viewing and Modifying Configuration
RS-232 Parity
[NONE]
Parity is used by the RS-232 hardware to verify data transmission. The
Parity value is dependent on the peripheral device you connect to the
RS-232 port. Check the documentation for your peripheral device to set
this value. Available parity check options for the E5810 are NONE, ODD,
EVEN, SPACE and MARK.
RS-232 SICL
Interface Name
[COM1]
This parameter is the symbolic name of the RS-232 Interface in the
E5810. It is used in an Agilent SICL
iopen operation to symbolically
reference the RS-232 interface in the E5810. It is also used in the
Remote RS-232 Serial Interface dialog (as
Interface name on remote Host)
when specifying an RS-232 device for Agilent VISA.
The RS-232 interface used by Agilent VISA or SICL must have a SICL
Interface Name. The maximum length of the RS-232 SICL Interface
Name is 15 characters.
RS-232 SRQ
[RI]
Method used to request service from the RS-232 device. The SRQ Line is
the modem status line on the RS-232 interface that is monitored for
Service ReQuests (SRQs). Available SRQ options for the E5810 are RI,
DCD, DSR, and CTS.
RS-232 Stop Bits
[1]
A bit that indicates that a byte has just been transmitted. Every byte of
data is preceded by a start bit and followed by a stop bit. Available stop
bit options are 1 or 2. Stop Bits is the number of bits used to indicate the
end of a character frame in RS-232 serial data transmission.
The Stop Bits value is dependent on the peripheral device you connect to
the RS-232 port. Check the documentation for your peripheral device to
set this value. Available stop bit options for the E5810 are 1 or 2.
Subnet Mask
[255.255.0.0]
This value is used to enable the E5810 to determine if a client IP address
is on the same local subnet as the E5810. When a client IP address is on
a different subnet, all packets must be sent to a subnet gateway.
See the
Glossary for an example of a subnet.
Parameter
[Default]
Description
- Agilent E5810A 1
- User’s Guide 1
- Front Matter 3
- Declaration of Conformity 4
- ICES Statement 5
- Regulatory Markings 5
- Safety Symbols 5
- WARNINGS 6
- Documentation History 7
- Copyright Information 7
- Support Information 7
- User’s Guide Information 8
- What’s in This 9
- Accessing an 10
- Electronic Copy of 10
- This Guide 10
- E5810A Related 10
- Documentation 10
- Table of Contents 11
- E5810A Description 13
- E5810 Hardware Description 15
- Local Network 16
- Connections 16
- Front Panel 17
- Display/LEDs 17
- Typical Power-On 18
- Sequence 18
- Preset Button 19
- 20 Chapter 1 20
- E5810A Software/Firmware 22
- E5810A Operating Features 23
- Client System 25
- Architecture 25
- How IO Application 26
- Software Works 26
- With the E5810 26
- Chapter 1 27 27
- E5810 IP Address 28
- Assignment 28
- Agilent IO Libraries Suite 29
- Using E5810 Web 30
- Using a Supported 31
- Programming 31
- Language 31
- Installing the E5810A 33
- Installation Flowchart 35
- Before You Install the E5810A 37
- Getting Network Information 39
- What is a Local Network? 41
- E5810 Hub/Switch 43
- Apply Power to the 45
- With Your PC 46
- Establishing 46
- Communication 46
- Configuring the 47
- E5810 for Enterprise 47
- Network Operation 47
- dialog box 48
- Chapter 2 49 49
- 50 Chapter 2 50
- Chapter 2 51 51
- Enter key 53
- 54 Chapter 2 54
- Click this icon 55
- Chapter 2 57 57
- Chapter 2 59 59
- for details 59
- 60 Chapter 2 60
- IO Libraries Suite 61
- 64 Chapter 2 64
- Chapter 2 67 67
- Using Interactive IO 68
- Example: Using 68
- Interactive IO 68
- Applicable 69
- Documents 69
- Addressing 71
- Instruments with 71
- Welcome page is the home 75
- Using the Welcome Page 76
- Navigation Bar 77
- E5810A Current Settings 78
- E5810A Support Information 79
- E5810A Documentation 80
- Chapter 3 81 81
- Displaying the 82
- Configuration Page 82
- E5810 Configuration 84
- Parameter 84
- Descriptions 84
- Chapter 3 85 85
- 86 Chapter 3 86
- Chapter 3 87 87
- 88 Chapter 3 88
- Chapter 3 89 89
- 90 Chapter 3 90
- Chapter 3 91 91
- Find and Control Instruments 92
- Connected to your E5810 92
- Using the Find 93
- Checking for 93
- Connected 93
- Instruments 93
- Querying 94
- Instruments Using 94
- Chapter 3 95 95
- Other Web Access Functions 97
- 98 Chapter 3 98
- Procedure to 99
- Update E5810 99
- Firmware 99
- Agilent FTP site is 100
- Accessible From 100
- Troubleshooting 104
- Guidelines 104
- Using E5810A Web Access 106
- Troubleshooting Information 107
- Troubleshooting Overview 109
- Checking the E5810A 110
- Checking Front 111
- Panel Display Error 111
- Messages 111
- 112 Chapter 4 112
- Checking E5810 113
- Current Parameters 113
- Resetting E5810 113
- Defaults 113
- Checking the Network 114
- Cache and Page 115
- E5810 Operation 117
- SICL Timeout 118
- Set to 0 (infinite) 118
- How to Verify PC 119
- Client Connections 119
- Example: Using the 120
- Message Description 122
- Example: Typical 123
- Chapter 4 125 125
- 126 Chapter 4 126
- Checking Instruments 127
- 128 Chapter 4 128
- E5810A Specifications 129
- Information 131
- 132 Appendix A 132
- Appendix A 133 133
- Supported Network Protocols 134
- Using the Telnet Utility 135
- Exiting the Telnet 138
- Typical Telnet 139
- Screen Display 139
- Glossary 143
- Glossary 145 145
- 146 Glossary 146
- Glossary 147 147
- 148 Glossary 148
- Glossary 149 149
- 150 Glossary 150
- Glossary 151 151
- 152 Glossary 152
- Glossary 153 153
- 154 Glossary 154
- Index 155 155
- 156 Index 156
- Index 157 157
- 158 Index 158
- Agilent Technologies 159
© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.018 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce