Agilent Technologies Ininiium 9000 Specifikace Strana 11
- Strana / 166
- Tabulka s obsahem
- ŘEŠENÍ PROBLÉMŮ
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
Chapter 1: General Information
Environmental Conditions
11
Environmental Conditions
Overvoltage Category
This product is intended to be powered by MAINS that comply to Overvoltage Category II, which is
typical of cord-and-plug connected equipment.
Pollution Degree
The 9000 Series Oscilloscope may be operated in environments of Pollution Degree 2 (or Pollution
Degree 1).
Pollution Degree Definitions
Pollution Degree 1: No pollution or only dry, non-conductive pollution occurs. The pollution has no
influence. Example: A clean room or climate controlled office environment.
Pollution Degree 2. Normally only dry non-conductive pollution occurs. Occasionally a temporary
conductivity caused by condensation may occur. Example: General indoor environment.
Pollution Degree 3: Conductive pollution occurs, or dry, non-conductive pollution occurs which
becomes conductive due to condensation which is expected. Example: Sheltered outdoor environment.
Measurement Category
Measurement Category
The 9000 Series oscilloscope is intended to be used for measurements in Measurement Category I.
Measurement Category Definitions
Measurement Category I is for measurements performed on circuits not directly connected to MAINS.
Examples are measurements on circuits not derived from MAINS, and specially protected (internal)
MAINS derived circuits. In the latter case, transient stresses are variable; for that reason, the transient
withstand capability of the equipment is made known to the user.
Measurement Category II is for measurements performed on circuits directly connected to the low
voltage installation. Examples are measurements on household appliances, portable tools and similar
equipment.
Measurement Category III is for measurements performed in the building installation. Examples are
measurements on distribution boards, circuit-breakers, wiring, including cables, bus-bars, junction
boxes, switches, socket-outlets in the fixed installation, and equipment for industrial use and some other
equipment, for example, stationary motors with permanent connection to the fixed installation.
Measurement Category IV is for measurements performed at the source of the low-voltage installation.
Examples are electricity meters and measurements on primary overcurrent protection devices and ripple
control units.
Transient Withstand Capability
The maximum transient withstand capability of this instrument is not specified. Do not apply more than
5 volts rms at the oscilloscope’s vertical input BNC connectors.
- Service Guide 1
- In This Book 3
- DC Gain Accuracy Test 59 5
- General Information 7
- Model Bandwidth 9
- DSO/MSO9104A 1 GHz bandwidth 9
- DSO/MSO9404A 4 GHz bandwidth 9
- Accessories supplied 10
- Environmental Conditions 11
- Measurement Category 11
- Oscilloscope Dimensions 12
- Setting Up the Oscilloscope 13
- To inspect package contents 15
- Technical Specifications 20
- 1 mV to < 10 mV/div: \2 V 21
- Figure 0-1 26
- To connect power 27
- Side Panel 29
- Probing the Circuit 31
- Figure 0-5 32
- To turn on the oscilloscope 33
- To turn off the oscilloscope 34
- To clean the oscilloscope 39
- Calibration 43
- To run the self calibration 45
- Testing Performance 47
- Performance Test Interval 48
- Performance Test Record 48
- Test Order 48
- Test Equipment 48
- • DC Gain Accuracy Test 50
- To test input impedance 51
- Offset Accuracy Test 52
- column (Offset 54
- Channel 1 57
- DC Gain Accuracy Test 59
- BNC (f) to dual banana 60
- (1251-2277) 60
- 6614C DC Supply 60
- Record the 62
- Click here and enter 16E-9 67
- Time Scale Accuracy (TSA) 72
- 9000A Oscilloscope 73
- E8257D Sine Wave Source 73
- Agilent Technologies 75
- Troubleshooting 83
- Default Setup 85
- Primary Trouble Isolation 87
- Self Calibration 90
- 4 of this service manual 90
- Assembly Level Repair 94
- Display Trouble Isolation 96
- Chapter 5: Troubleshooting 100
- Front Panel Trouble Isolation 102
- Motherboard Verification 103
- To setup the BIOS 104
- To check the LEDs 109
- Software Revisions 110
- To check probe power outputs 111
- Replacing Assemblies 113
- Remove these two screws 117
- Then remove this 136
- Perform self tests 140
- Performance calibration 140
- Replaceable Parts 145
- Exploded Views 147
- Chapter 7: Replaceable Parts 148
- Replaceable Parts List 151
- Theory of Operation 155
- XC 3 S 1 0 0 158
- Block-Level Theory 160
- Chapter : 162
Související produkty a manuály pro Měření, testování a kontrola Agilent Technologies Ininiium 9000
(224 stránky)© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.069 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce