Agilent Technologies Agilent 8166A Manuál s instrukcemi Strana 237
- Strana / 274
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
Lambda Scan Applications The Agilent 816x VXIplug&play Instrument Driver
Agilent 8163A/B, 8164A/B & 8166A/B Mainframes, Fifth Edition 237
How to Perform a Lambda Scan Application
Figure 19 Lambda Scan Operation Setup
The Prepare Lambda Scan Function
The Prepare Lambda Scan (hp816x_prepareLambdaScan) function
prepares a Lambda Scan operation.
The Prepare Lambda Scan (hp816x_prepareLambdaScan) function must
be called before a Lambda Scan operation is executed. Use the return
values of this function (Number of Datapoints and Number of Power
Arrays) to allocate arrays for the Execute Lambda Scan
(hp816x_executeLambdaScan) function.
To obtain a higher precision, the Tunable Laser Source is set 1 nm before
the Start Wavelength, this means, you have to choose a Start Wavelength
1 nm greater than the minimum possible wavelength. Also, the wavelength
sweep is actually started 90 pm before the Start Wavelength and ends 90
pm after the Stop Wavelength, this means, you have to choose a Stop
Wavelength 90 pm less than the maximum possible wavelength.
Triggers coordinate the Tunable Laser module with all Power Meters. The
function sets for the lowest possible averaging time available for the
installed Power Meters and, then, sets the highest possible sweep speed
for the selected Tunable Laser module sweep.
If one of the following circumstances occurs, the "parameter mismatch"
error will be returned:
1 If one Power Meter is out of the specification at 1550 nm, the error
"powermeter wavelength does not span 1550nm" will be returned. For
example, the HP 81530A Power Sensor and the HP 81520A Optical Head
are out of specification at 1550 nm. Remove the Power Meter that is out
of specification at 1550 nm from the mainframe.
- Programming Guide 1
- 08164-90B64 2
- Warnings and Notices 3
- In this Manual 5
- Related Manuals 6
- Table of Contents 7
- Specific Commands 43 8
- VISA Programming Examples 189 9
- Error Codes 257 10
- Index 271 10
- List of Figures 11
- List of Tables 13
- Introduction to Programming 15
- GPIB Interface 16
- Figure 1 Remote Control 18
- Message Queues 19
- How the Input Queue Works 20
- The Output Queue 21
- The Error Queue 22
- Programming and Syntax 23
- Diagram Conventions 23
- Short Form and Long Form 24
- Command and Query Syntax 25
- Data Types 26
- Slot and Channel Numbers 26
- Laser Selection Numbers 27
- Common Commands 29
- Common Command Summary 30
- Common Status Information 31
- The Status Model 33
- Status Byte Register 35
- Status Summary 35
- Status System for 8166A/B 36
- Annotations 37
- Status Command Summary 40
- Other Commands 41
- Specific Commands 43
- Specific Command Summary 44
- page 154 46
- :TRIGger 53
- :TRIGger:CONFiguration 53
- :TRIGger[n][CHANnel[m]] 53
- Instrument Setup and Status 55
- IEEE-Common Commands 56
- • GPIB (interface) state 61
- • Output queue 61
- Settings – The SYSTem 76
- → +20<END> 78
- Root Layer Command 80
- → #536570 83
- → 1200e-6,2.019\n 1210e-6 84
- Measurement Functions – The 85
- SENSe Subsystem 85
- Measurement Running 94
- Measurement Stopped 94
- → interpreted as 98
- → +1.00000000E+000<END> 102
- → -2.00000000E+001<END> 103
- → 1<END> 104
- → +6.5000E+001 110
- → +8.00000000E-002<END> 111
- → +1.80000000E-001<END> 112
- Subsystem 113
- → HIGH<END> 114
- → +0<END> 116
- → 0<END> 117
- → 50<END> 118
- → +1<END> 119
- → +4.00000E+03<END> 120
- → +8.000E+01<END> 121
- [PM 130
- → -1.00000000E+013<END> 135
- → +1.5500000E-006<END> 135
- <wsp> 137
- <value> 137
- → +3<END> 137
- → +5.00000000E-001<END> 138
- → STEP<END> 141
- → ONEW<END> 142
- → +5.00000000E-008<END> 143
- → +1.50000000E-006<END> 144
- → +1.55000000E-006<END> 145
- manual sweep 146
- → +5.00000000E-009<END> 147
- Signal Conditioning 148
- → 2<END> 149
- → 12<END> 152
- → 6<END> 153
- Offset ( λ ) 161
- → +2,+1<END> 162
- UM 163
- 163
- → 1000 entries) 164
- Slot Numbers 165
- Command Semantic 166
- Display and System Commands 167
- IEEE Commands 167
- Status Commands 168
- User Calibration Data 168
- Signal Routing 169
- Triggering - The TRIGger 171
- → ign<END> 174
- → 5<END> 175
- → dis<END> 176
- ..... 180
- Tun able 182
- Display Operations – The 186
- DISPlay Subsystem 186
- VISA Programming Examples 189
- How to Use VISA Calls 190
- How to Set up a Fixed Laser 192
- How to Measure Power using 195
- FETCh and READ 195
- How to Co-ordinate Two 199
- How Power Varies with 203
- Wavelength 203
- How to Log Results 207
- Installing the Agilent 816x 214
- Instrument Driver 214
- Using Visual Programming 218
- Environments 218
- Getting Started with LabView 221
- Features of the Agilent 816x 225
- Directory Structure 226
- Opening an Instrument Session 227
- Closing an Instrument Session 228
- VISA Data Types and Selected 229
- Constant Definitions 229
- Error Handling 230
- Agilent VEE 5.01 (or higher) 233
- Online Information 234
- Lambda Scan Applications 235
- Equally Spaced Datapoints 236
- Scan Application 239
- Laser Source 245
- Compatibility Issues 246
- Status Model 247
- Preset Defaults 248
- Removed Command 249
- Obsolete Commands 250
- Changed Parameter Syntax and 251
- Semantics 251
- Changed Query Result Values 252
- Timing Behavior 253
- Command Order 255
- Instrument Status Settings 256
- Error Codes 257
- GPIB Error Strings 258
- Agilent Technologies 274
Související produkty a manuály pro Multimetry Agilent Technologies Agilent 8166A
Multimetry Agilent Technologies 8487D Specifikace
(144 stránky)
(144 stránky)
Multimetry Agilent Technologies 22D Specifikace
(118 stránky)
(118 stránky)
Multimetry Agilent Technologies U1252A Servisní příručka
(185 stránky)
(185 stránky)
(21 stránky)
Multimetry Agilent Technologies 8568B Specifikace
(118 stránky)
(118 stránky)
MotoChello manuales
La lista de dispositivos de MotoChello contiene 1 manuales de usuario y guías para 1 modelos en 2 tipo de dispositivos
Komentáře k této Příručce