Agilent Technologies 8133A Servisní příručka Strana 30
- Strana / 188
- Tabulka s obsahem
- ŘEŠENÍ PROBLÉMŮ
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
30 16800 Series Portable Logic Analyzers Service Guide
3 Testing Performance
2 Solder the pin strip to the SMA board mount connector:
a Solder the leads on the left side of the pin strip to the
center conductor of the SMA connector as shown in
the diagram below.
b Solder the leads on the right side of the pin strip to
the inside of the SMA connector’s frame as shown in
the diagram below. Use a small amount of solder.
3 Attach the second SMA board mount connector:
a Re-heat the solder connection made in the previous
step, and attach the second SMA connector, as shown
in the diagram below. Note that the second SMA
connector is upside- down, compared to the first. Add a
little solder to make a good connection.
b Solder the center conductor of the second SMA
connector to the center conductor of the first SMA
connector and the leads on the left side of the pin
strip.
c Rotate the assembly 180 degrees and solder the two
SMA board mount connector frames together.
4 Check your work:
a Ensure that the following four points have continuity
between them: The two pins on the left side of the pin
solder
- Agilent 16800 Series 1
- Portable Logic Analyzers 1
- Model Comparison 3
- Features, Logic Acquisition 3
- Features, Mainframe 4
- Features, Pattern Generator 4
- Supplied Accessories 4
- Optional Accessories: 4
- Service Strategy 4
- In this Service Guide 6
- 4 Calibrating and Adjusting 8
- 7 Replaceable Parts 10
- 8 Theory of Operation 10
- Contents 11
- General Information 13
- Accessories 14
- Specifications 15
- Characteristics 16
- Non-Operating Environment 17
- Dimensions 18
- Recommended Test Equipment 19
- 1 General Information 20
- Preparing for Use 21
- To inspect the logic analyzer 22
- To apply power 22
- To clean the instrument 23
- To start the user interface 23
- To test the logic analyzer 23
- 2 Preparing for Use 24
- Testing Performance 25
- To perform the power-up tests 26
- Logic Analyzer Test Strategy 27
- 3 Testing Performance 28
- Testing Performance 3 31
- Equipment Required 34
- Perform System Self-Tests 36
- Set Up the Test Equipment 37
- Connect the Test Equipment 39
- Deskew the oscilloscope 42
- Set the 8133A pulse width 43
- Configure the Logic Analyzer 45
- Run eye finder 49
- To re-align a stray channel 50
- Test Pod 1 in 250 Mb/s Mode 52
- Test Pod 2 in 250 Mb/s Mode 57
- Test the remaining pods 59
- Test Pod 1 in 500 Mb/s Mode 60
- Test Pod 2 in 500 Mb/s Mode 64
- Conclude the State Mode Tests 66
- Performance Test Record 68
- Calibrating and Adjusting 69
- Calibration Strategy 70
- Troubleshooting 71
- Try , and then 75
- Power Supplies 84
- To run the self-tests 88
- Bit#: 39 - 16 15 - 8 7 - 0 92
- Clock Test 93
- Simple RAM Test 93
- RAM Persistence Test 94
- Marching Bits RAM Test 94
- Wait Test 94
- Instruction Interrupt Test 95
- To exit the test system 96
- 5 Troubleshooting 100
- Set up the test equipment 101
- Connect the test equipment 101
- Threshold 102
- Troubleshooting 5 109
- Clock Frequency of 100 MHz 111
- Click Run Rep 111
- Replacing Assemblies 113
- Replacement Strategy 114
- Tools Required 114
- To save the license file 115
- To power off the system 116
- Replacing Assemblies 6 117
- 6 Replacing Assemblies 118
- 600 watt power supply 119
- Secondary power supply 120
- 60 mm fan 144
- 92 mm fans 145
- Returning Assemblies 148
- FRAGILE 149
- Replaceable Parts 151
- Ordering Replaceable Parts 152
- System Replaceable Parts List 155
- Replaceable Parts 7 159
- • A — Assembly 163
- • MP — Mechanical Part 163
- • W — Cable 163
- Theory of Operation 167
- System Block Level Theory 168
- Module Interface Board (MIB) 169
- CPU Subsystem 170
- PCI board 171
- MIB (Module Interface Board) 171
- Module Bus FPGA(s) 172
- I/O FPGA 172
- Theory of Operation 8 173
- Front Panel Assembly 174
- Power Up Routine 175
- Product install 178
- Software recovery methods 178
- Self Test 179
- Comparators 181
- Acquisition IC 181
- Master/Expander Connectors 182
- Instruction Memory 183
- Data Memory 183
- Output Driver 184
- Clock Circuit 184
- CPU Interface 184
Související produkty a manuály pro Měření, testování a kontrola Agilent Technologies 8133A
(145 stránky)© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.039 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce