Agilent Technologies 8133A Servisní příručka Strana 98
- Strana / 188
- Tabulka s obsahem
- ŘEŠENÍ PROBLÉMŮ
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
98 16800 Series Portable Logic Analyzers Service Guide
5 Troubleshooting
To test the logic acquisition cables
This test allows you to functionally verify the logic analyzer
cable and the flying lead probe of any of the logic analyzer
pods. Only one probe and cable can be tested at a time.
Repeat this test for each probe and cable to be tested. Two
Flying Lead Probes are required if you need to test pods
other than Pod 1 because the clock from Pod 1 will be used
to acquire data.
To assemble the 2 x 9 test connectors
The 2 x 9 test connectors are used to connect all 16
channels and the clock of the logic analyzer to the pulse
generator so you can test the flying lead probe and cables.
(See “To test the logic acquisition cables" on page 98.)
Table 12 Equipment Required to Test Cables
Equipment Critical Specification Recommended Model/Part
Pulse Generator 40 MHz, 3 ns pulse width,
< 600 ps rise time
8133A Option 003
2 x 9 Test Connectors
(Qty 2)
no substitute See “To assemble the 2 x 9 test
connectors" on page 98.
SMA m-m adapter
(Qty 2)
Johnson 142-0901-811 SMA Plug to
Plug or similar
Flying Lead Probe
(Qty 2)
no substitute HP or Agilent E5383A
Table 13 Materials Required for the 2 x 9 Test Connectors
Material Critical Specification Recommended Model/Part
Pin Strip Header
(Qty 1, which will be separated)
.100" x .100" Pin Strip Header, straight,
pin length .230", two rows, .120" solder
tails, 2 x 40 contacts
3M 2380-6121TN or similar 2- row with
0.1” pin spacing
Jumper wire <6 inches, approximately 22 gauge
Resistor, 100 ohm 1%
(Qty 4)
SMA Board Mount Connector
(Qty 2)
Johnson 142-0701-801
(see www.johnsoncomponents.com)
- Agilent 16800 Series 1
- Portable Logic Analyzers 1
- Model Comparison 3
- Features, Logic Acquisition 3
- Features, Mainframe 4
- Features, Pattern Generator 4
- Supplied Accessories 4
- Optional Accessories: 4
- Service Strategy 4
- In this Service Guide 6
- 4 Calibrating and Adjusting 8
- 7 Replaceable Parts 10
- 8 Theory of Operation 10
- Contents 11
- General Information 13
- Accessories 14
- Specifications 15
- Characteristics 16
- Non-Operating Environment 17
- Dimensions 18
- Recommended Test Equipment 19
- 1 General Information 20
- Preparing for Use 21
- To inspect the logic analyzer 22
- To apply power 22
- To clean the instrument 23
- To start the user interface 23
- To test the logic analyzer 23
- 2 Preparing for Use 24
- Testing Performance 25
- To perform the power-up tests 26
- Logic Analyzer Test Strategy 27
- 3 Testing Performance 28
- Testing Performance 3 31
- Equipment Required 34
- Perform System Self-Tests 36
- Set Up the Test Equipment 37
- Connect the Test Equipment 39
- Deskew the oscilloscope 42
- Set the 8133A pulse width 43
- Configure the Logic Analyzer 45
- Run eye finder 49
- To re-align a stray channel 50
- Test Pod 1 in 250 Mb/s Mode 52
- Test Pod 2 in 250 Mb/s Mode 57
- Test the remaining pods 59
- Test Pod 1 in 500 Mb/s Mode 60
- Test Pod 2 in 500 Mb/s Mode 64
- Conclude the State Mode Tests 66
- Performance Test Record 68
- Calibrating and Adjusting 69
- Calibration Strategy 70
- Troubleshooting 71
- Try , and then 75
- Power Supplies 84
- To run the self-tests 88
- Bit#: 39 - 16 15 - 8 7 - 0 92
- Clock Test 93
- Simple RAM Test 93
- RAM Persistence Test 94
- Marching Bits RAM Test 94
- Wait Test 94
- Instruction Interrupt Test 95
- To exit the test system 96
- 5 Troubleshooting 100
- Set up the test equipment 101
- Connect the test equipment 101
- Threshold 102
- Troubleshooting 5 109
- Clock Frequency of 100 MHz 111
- Click Run Rep 111
- Replacing Assemblies 113
- Replacement Strategy 114
- Tools Required 114
- To save the license file 115
- To power off the system 116
- Replacing Assemblies 6 117
- 6 Replacing Assemblies 118
- 600 watt power supply 119
- Secondary power supply 120
- 60 mm fan 144
- 92 mm fans 145
- Returning Assemblies 148
- FRAGILE 149
- Replaceable Parts 151
- Ordering Replaceable Parts 152
- System Replaceable Parts List 155
- Replaceable Parts 7 159
- • A — Assembly 163
- • MP — Mechanical Part 163
- • W — Cable 163
- Theory of Operation 167
- System Block Level Theory 168
- Module Interface Board (MIB) 169
- CPU Subsystem 170
- PCI board 171
- MIB (Module Interface Board) 171
- Module Bus FPGA(s) 172
- I/O FPGA 172
- Theory of Operation 8 173
- Front Panel Assembly 174
- Power Up Routine 175
- Product install 178
- Software recovery methods 178
- Self Test 179
- Comparators 181
- Acquisition IC 181
- Master/Expander Connectors 182
- Instruction Memory 183
- Data Memory 183
- Output Driver 184
- Clock Circuit 184
- CPU Interface 184
Související produkty a manuály pro Měření, testování a kontrola Agilent Technologies 8133A
(145 stránky)© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.021 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce