Agilent Technologies 8000 Series Návod k obsluze Strana 112
- Strana / 126
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
112 8000 Operator’s Manual
5 Maintenance and Troubleshooting
9 Upon completion of the cleaning process, the 8000 dispensing arm
and the Apparatus 3 / 7 drive unit return to the home position.
Syringe and Seal Replacement
1 Disconnect all sample tubes from the pump.
2 On the 8000, press MENU > 7 > 6 > 3 to partially extend the syringe
plungers.
3 When the syringe plungers reach approximately 5 mL, turn off the
pump.
4 Disconnect the power cord and communication cables from the
pump.
5 Remove the syringe plunger thumb screw(s).
6 Using a #2 Phillips screwdriver, remove the 4 screws that secure the
retainer block at the top of the syringes.
7 Carefully remove the syringe valve retainer block.
8 Flip the pump so that it is sitting on its top.
9 For improved access to the syringe ferrule, gently slide the syringe
away from the pump while disengaging the plunger and valve from
their locating pins.
10 Unscrew the syringe from the valve using care not to break the glass.
11 If there is a seal within the syringe port on the valve, extract it from
the port.
NOTE
If the syringe seal eventually develops a leak, retighten the syringe by
hand (18 - 21 oz-in, 1.3 - 1.5 Kg-cm).
If the seal eventually obstructs the media path, new seals are available
for purchase (P/N K1002-00438).
CAUTION
The distance that the valve will move out of the pump is limited by
the valve wires. Use care not to break or damage the valve wires.
- Agilent 8000 1
- Dissolution Sampling 1
- Contents 3
- 4 8000 Operator’s Manual 4
- 8000 Operator’s Manual 5 5
- 6 8000 Operator’s Manual 6
- 8000 Operator’s Manual 7 7
- 8 8000 Operator’s Manual 8
- 8000 Operator’s Manual 9 9
- 10 8000 Operator’s Manual 10
- Electrical Hazards 12
- Information Symbols 14
- Introduction 15
- 8000 with Peristaltic Pump 17
- CC1234xxxx 18
- Setting Up the 8000 19
- Unpacking Your 8000 21
- Installation 22
- Setup of 8000 and Components 34
- Installing the Sample Tray 36
- (Peristaltic Pump only) 37
- Installing the RM Module 38
- External Unit 39
- Hidden Key Functions 41
- 42 8000 Operator’s Manual 42
- 3 Setting Up the 8000 42
- Table 1 Hidden Key Functions 42
- Setting Up the 8000 3 43
- 8000 Operator’s Manual 43 43
- 44 8000 Operator’s Manual 44
- Operating the 8000 45
- 8000 Keypad Options 46
- Operating the 8000 4 47
- 8000 Operator’s Manual 47 47
- Main Menu 48
- 8000 Operator’s Manual 49 49
- 50 8000 Operator’s Manual 50
- 52 8000 Operator’s Manual 52
- 54 8000 Operator’s Manual 54
- 56 8000 Operator’s Manual 56
- 60 8000 Operator’s Manual 60
- Creating a Sample Program 61
- 8000 Operator’s Manual 63 63
- 64 8000 Operator’s Manual 64
- SAMPLE TIME POINT: 000:02 65
- Starting a 8000 Program 66
- 68 8000 Operator’s Manual 68
- DISSO Options Screen 69
- 70 8000 Operator’s Manual 70
- 8000 Operator’s Manual 71 71
- 8000 Operator’s Manual 73 73
- 8000 Operator’s Manual 75 75
- 76 8000 Operator’s Manual 76
- 78 8000 Operator’s Manual 78
- 82 8000 Operator’s Manual 82
- ON R-M PUMP displays 84
- 8000 Operator’s Manual 85 85
- 88 8000 Operator’s Manual 88
- 8000 Operator’s Manual 89 89
- Starting a Program 91
- APP 3/7 Options Screen 93
- 94 8000 Operator’s Manual 94
- Table 2 4 App 3/7 Options 94
- Manual Sample 95
- 96 8000 Operator’s Manual 96
- Automatic Calibration 97
- 1 MANUAL 2 AUTOMATIC 98
- Manual Calibration 99
- Daisy Chaining 102
- 104 8000 Operator’s Manual 104
- 4 Operating the 8000 104
- Agilent Technologies 105
- Preventive Maintenance 106
- Apparatus 3 / 7 107
- Start Immediately 108
- Programmed Clean 108
- Apparatus 1 / 2 111
- Syringe and Seal Replacement 112
- Cleaning the Syringes 113
- Filter Changer (optional) 115
- Report Center Impact Printer 119
- Replacing a Paper Roll 120
- Toggling Your Printer Online 121
- Printer Self Test 121
- Printer Configuration 122
- 124 8000 Operator’s Manual 124
- 8000 Operator’s Manual 125 125
- 126 8000 Operator’s Manual 126
Související produkty a manuály pro Tisk a skenování Agilent Technologies 8000 Series
(82 stránky)© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.396 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce