Agilent Technologies 8000 Series Návod k obsluze Strana 88
- Strana / 126
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
88 8000 Operator’s Manual
4 Operating the 8000
Following is a description of the Program Variables screen options:
Table 2 2 Program Variables Options (Apparatus 3 / 7)
Option Function
1 Set APP 3/7 Parameters Use this option to set the Apparatus 3 / 7 parameters. Select option 1, Set APP 3/7
Parameters. The Set APP 3/7 Parameters screen displays. See “Main Menu Option 2 -
Set DISSO” on page 53 for a description of the Set APP 3/7 Parameters screen options.
2 Sample Time Points Use this option to enter the sample time points. See “Program Option 2 - Sample Time
Points” on page 90.
3 Sample Volume Select option 3, Sample Volume. Enter the sample volume in milliliters and press
ENTER. The Program Variables screen displays. You can enter the volume with up to
three digits (for example 13.5) so that fractional milliliters can be collected. Verify the
collection tubes can hold the requested volume.
Note: The maximum volume accepted is 14 mL.
4 Headers Select option 4, Headers. The Batch # Selections screen displays. For each option, enter
the desired information and press ENTER. The Program Variables screen displays.
Note: The Batch # Selections screen displays options for the report header information.
The print field accepts ten characters. Characters can be letters, numbers, special
characters, or spaces. The information entered for each selection prints in the header of
each printout. The entries made from this menu are attached to the active program.
Since there are 15 programs, there can be a different set of entries for each. All are
stored in the battery-protected memory and remain until changed via this menu.
5 Prime Time (peristaltic
pump)
If your system configuration includes the peristaltic pump, use this option to set the
interval the peristaltic pump runs forward, drawing medium into the system, before the
valves open to deliver samples.
Select option 5, Prime Time. Enter a value for the priming time from 1 to 99 seconds
and press ENTER. The Program Variables screen displays.
Note: At a minimum, the prime time should be long enough for medium to be seen
dripping from the return cannulas. In general, the longer the tubing lengths, the longer
the priming time required.
5 Prime Volume (syringe
pump)
If your system configuration includes the syringe pump, use this option to set the
amount of drawn medium necessary to fill the sampling lines of the entire system.
Select option 5, Prime Volume. Enter a value for the priming volume and press
ENTER. The Program Variables screen displays.
Note: At a minimum, the prime volume should be large enough for medium to be seen
dripping from the return cannulas. In general, the longer the tubing lengths, the larger
the prime volume required.
- Agilent 8000 1
- Dissolution Sampling 1
- Contents 3
- 4 8000 Operator’s Manual 4
- 8000 Operator’s Manual 5 5
- 6 8000 Operator’s Manual 6
- 8000 Operator’s Manual 7 7
- 8 8000 Operator’s Manual 8
- 8000 Operator’s Manual 9 9
- 10 8000 Operator’s Manual 10
- Electrical Hazards 12
- Information Symbols 14
- Introduction 15
- 8000 with Peristaltic Pump 17
- CC1234xxxx 18
- Setting Up the 8000 19
- Unpacking Your 8000 21
- Installation 22
- Setup of 8000 and Components 34
- Installing the Sample Tray 36
- (Peristaltic Pump only) 37
- Installing the RM Module 38
- External Unit 39
- Hidden Key Functions 41
- 42 8000 Operator’s Manual 42
- 3 Setting Up the 8000 42
- Table 1 Hidden Key Functions 42
- Setting Up the 8000 3 43
- 8000 Operator’s Manual 43 43
- 44 8000 Operator’s Manual 44
- Operating the 8000 45
- 8000 Keypad Options 46
- Operating the 8000 4 47
- 8000 Operator’s Manual 47 47
- Main Menu 48
- 8000 Operator’s Manual 49 49
- 50 8000 Operator’s Manual 50
- 52 8000 Operator’s Manual 52
- 54 8000 Operator’s Manual 54
- 56 8000 Operator’s Manual 56
- 60 8000 Operator’s Manual 60
- Creating a Sample Program 61
- 8000 Operator’s Manual 63 63
- 64 8000 Operator’s Manual 64
- SAMPLE TIME POINT: 000:02 65
- Starting a 8000 Program 66
- 68 8000 Operator’s Manual 68
- DISSO Options Screen 69
- 70 8000 Operator’s Manual 70
- 8000 Operator’s Manual 71 71
- 8000 Operator’s Manual 73 73
- 8000 Operator’s Manual 75 75
- 76 8000 Operator’s Manual 76
- 78 8000 Operator’s Manual 78
- 82 8000 Operator’s Manual 82
- ON R-M PUMP displays 84
- 8000 Operator’s Manual 85 85
- 88 8000 Operator’s Manual 88
- 8000 Operator’s Manual 89 89
- Starting a Program 91
- APP 3/7 Options Screen 93
- 94 8000 Operator’s Manual 94
- Table 2 4 App 3/7 Options 94
- Manual Sample 95
- 96 8000 Operator’s Manual 96
- Automatic Calibration 97
- 1 MANUAL 2 AUTOMATIC 98
- Manual Calibration 99
- Daisy Chaining 102
- 104 8000 Operator’s Manual 104
- 4 Operating the 8000 104
- Agilent Technologies 105
- Preventive Maintenance 106
- Apparatus 3 / 7 107
- Start Immediately 108
- Programmed Clean 108
- Apparatus 1 / 2 111
- Syringe and Seal Replacement 112
- Cleaning the Syringes 113
- Filter Changer (optional) 115
- Report Center Impact Printer 119
- Replacing a Paper Roll 120
- Toggling Your Printer Online 121
- Printer Self Test 121
- Printer Configuration 122
- 124 8000 Operator’s Manual 124
- 8000 Operator’s Manual 125 125
- 126 8000 Operator’s Manual 126
Související produkty a manuály pro Tisk a skenování Agilent Technologies 8000 Series
(82 stránky)Case-mate Non manuels d'utilisation
La liste de Case-mate Non produits contient 1 manuels d'utilisation pour les modèles 1. Tous les guides d'utilisation en format pdf peuvent être téléchargés ou consultés en ligne.
Komentáře k této Příručce