Agilent Technologies 8000 Series Návod k obsluze Strana 35
- Strana / 126
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
Setting Up the 8000 3
8000 Operator’s Manual 35
• If your system configuration includes the syringe pump, the power
receptacle, and power switch are located on the left side of the unit.
Connect the power cord and turn on the syringe pump.
• If your system configuration includes the filter changer, the power
receptacle, and power switch are located on the rear of the unit.
Connect the power cord and turn on the filter changer.
The 8000 has a dual voltage (115 V / 230 V) option on the power entry
module. Ensure the voltage indicated on the fuse drawer matches the
power outlet. Connect the power cord to the rear of the 8000. Turn on
the 8000. The system monitor illuminates. The system monitor displays
the initial status screen and then changes to the Ready screen.
The firmware version (program revision) displays. This is the only time
the firmware version displays. Record the number below and refer to it
if you need to call the Dissolution Systems Service Department.
While the unit is powering up, the dispensing arm returns to its home
position at the rear of the unit and the firmware program initializes. If
the dispensing arm is already at the home position when the unit is
powered up, the initial status screen displays for three seconds only.
When the initial status screen disappears, the Ready screen displays.
From the Ready screen, you can access the Main Menu or any of the
manual functions.
8000 FRACTION COLLECTOR
PROGRAM REVISION x.xx
INITIALIZING....PLEASE WAIT
TIME: 01/01/12 21:56:40 ELAPSE: 000:00:00
Firmware version
READY
PRG# 01 R-M: ENABLED VOLUME: 5 mL
TIME: 01/01/12 21:56:40 ELAPSE: 000:00:00
- Agilent 8000 1
- Dissolution Sampling 1
- Contents 3
- 4 8000 Operator’s Manual 4
- 8000 Operator’s Manual 5 5
- 6 8000 Operator’s Manual 6
- 8000 Operator’s Manual 7 7
- 8 8000 Operator’s Manual 8
- 8000 Operator’s Manual 9 9
- 10 8000 Operator’s Manual 10
- Electrical Hazards 12
- Information Symbols 14
- Introduction 15
- 8000 with Peristaltic Pump 17
- CC1234xxxx 18
- Setting Up the 8000 19
- Unpacking Your 8000 21
- Installation 22
- Setup of 8000 and Components 34
- Installing the Sample Tray 36
- (Peristaltic Pump only) 37
- Installing the RM Module 38
- External Unit 39
- Hidden Key Functions 41
- 42 8000 Operator’s Manual 42
- 3 Setting Up the 8000 42
- Table 1 Hidden Key Functions 42
- Setting Up the 8000 3 43
- 8000 Operator’s Manual 43 43
- 44 8000 Operator’s Manual 44
- Operating the 8000 45
- 8000 Keypad Options 46
- Operating the 8000 4 47
- 8000 Operator’s Manual 47 47
- Main Menu 48
- 8000 Operator’s Manual 49 49
- 50 8000 Operator’s Manual 50
- 52 8000 Operator’s Manual 52
- 54 8000 Operator’s Manual 54
- 56 8000 Operator’s Manual 56
- 60 8000 Operator’s Manual 60
- Creating a Sample Program 61
- 8000 Operator’s Manual 63 63
- 64 8000 Operator’s Manual 64
- SAMPLE TIME POINT: 000:02 65
- Starting a 8000 Program 66
- 68 8000 Operator’s Manual 68
- DISSO Options Screen 69
- 70 8000 Operator’s Manual 70
- 8000 Operator’s Manual 71 71
- 8000 Operator’s Manual 73 73
- 8000 Operator’s Manual 75 75
- 76 8000 Operator’s Manual 76
- 78 8000 Operator’s Manual 78
- 82 8000 Operator’s Manual 82
- ON R-M PUMP displays 84
- 8000 Operator’s Manual 85 85
- 88 8000 Operator’s Manual 88
- 8000 Operator’s Manual 89 89
- Starting a Program 91
- APP 3/7 Options Screen 93
- 94 8000 Operator’s Manual 94
- Table 2 4 App 3/7 Options 94
- Manual Sample 95
- 96 8000 Operator’s Manual 96
- Automatic Calibration 97
- 1 MANUAL 2 AUTOMATIC 98
- Manual Calibration 99
- Daisy Chaining 102
- 104 8000 Operator’s Manual 104
- 4 Operating the 8000 104
- Agilent Technologies 105
- Preventive Maintenance 106
- Apparatus 3 / 7 107
- Start Immediately 108
- Programmed Clean 108
- Apparatus 1 / 2 111
- Syringe and Seal Replacement 112
- Cleaning the Syringes 113
- Filter Changer (optional) 115
- Report Center Impact Printer 119
- Replacing a Paper Roll 120
- Toggling Your Printer Online 121
- Printer Self Test 121
- Printer Configuration 122
- 124 8000 Operator’s Manual 124
- 8000 Operator’s Manual 125 125
- 126 8000 Operator’s Manual 126
Související produkty a manuály pro Tisk a skenování Agilent Technologies 8000 Series
(82 stránky)© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.025 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce