Agilent Technologies 8000 Series Návod k obsluze Strana 56
- Strana / 126
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
56 8000 Operator’s Manual
4 Operating the 8000
3 Prime Loss Volume Use this option to configure the prime loss volume. Prime loss volume
compensates for the volume of medium used to fill the tubing between the
sampling cannulas and sampling valves during the priming cycle. When sampling,
an amount of sample equal to the prime loss volume flows past the valves in the
8000 before the valves open to collect sample. The program also restricts this
volume to be less than or equal to the syringe size volume.
Select option 3, Prime Loss Volume. Enter a prime loss volume based on the
sample tubing length, inner diameter, and system dead volumes and press
ENTER. The Set Syringe Pump Parameters screen displays.
If the tubing length between the sampling cannulas and sampling valves is
changed, adjust the prime loss volume accordingly.
4 Aspirt. Dwell Time Use this option to configure the aspiration dwell time. Aspiration dwell time is the
time the syringe plunger pauses at the bottom of a stroke to allow the medium
being drawn to overcome the vacuum generated by the drawn plunger.
Select option 4, Aspirt. Dwell Time. Enter an aspiration dwell time between 1 and
10 seconds and press ENTER The recommended time is 10 seconds. The Set
Syringe Pump Parameters screen displays.
5 Full Stroke (hidden
option)
Use this option to configure the number of steps the stepper motor makes to draw
the syringe plunger its maximum stroke length.
Select option 5, Full Stroke. Enter a full stroke value between 0 and 19999 and
press ENTER. The recommended value is 19300. The Set Syringe Pump
Parameters screen displays.
If the volume dispensed by the syringe is outside of the required specifications, the
full stroke value can be adjusted using the following calculation and solving for x:
target volume (mL)
= avg volume dispensed (mL)
x 19300
6 Pump Current (hidden
option)
Use this option to configure the pump current. The use of more viscous media
requires a higher pump current.
Select option 6, Pump Current. Enter a pump current between 0 and 8 and press
ENTER. The recommended value is 4. The Set Syringe Pump Parameters screen
displays.
Table 6 Set Syringe Pump Parameters (Apparatus 1 / 2)
Option Function
- Agilent 8000 1
- Dissolution Sampling 1
- Contents 3
- 4 8000 Operator’s Manual 4
- 8000 Operator’s Manual 5 5
- 6 8000 Operator’s Manual 6
- 8000 Operator’s Manual 7 7
- 8 8000 Operator’s Manual 8
- 8000 Operator’s Manual 9 9
- 10 8000 Operator’s Manual 10
- Electrical Hazards 12
- Information Symbols 14
- Introduction 15
- 8000 with Peristaltic Pump 17
- CC1234xxxx 18
- Setting Up the 8000 19
- Unpacking Your 8000 21
- Installation 22
- Setup of 8000 and Components 34
- Installing the Sample Tray 36
- (Peristaltic Pump only) 37
- Installing the RM Module 38
- External Unit 39
- Hidden Key Functions 41
- 42 8000 Operator’s Manual 42
- 3 Setting Up the 8000 42
- Table 1 Hidden Key Functions 42
- Setting Up the 8000 3 43
- 8000 Operator’s Manual 43 43
- 44 8000 Operator’s Manual 44
- Operating the 8000 45
- 8000 Keypad Options 46
- Operating the 8000 4 47
- 8000 Operator’s Manual 47 47
- Main Menu 48
- 8000 Operator’s Manual 49 49
- 50 8000 Operator’s Manual 50
- 52 8000 Operator’s Manual 52
- 54 8000 Operator’s Manual 54
- 56 8000 Operator’s Manual 56
- 60 8000 Operator’s Manual 60
- Creating a Sample Program 61
- 8000 Operator’s Manual 63 63
- 64 8000 Operator’s Manual 64
- SAMPLE TIME POINT: 000:02 65
- Starting a 8000 Program 66
- 68 8000 Operator’s Manual 68
- DISSO Options Screen 69
- 70 8000 Operator’s Manual 70
- 8000 Operator’s Manual 71 71
- 8000 Operator’s Manual 73 73
- 8000 Operator’s Manual 75 75
- 76 8000 Operator’s Manual 76
- 78 8000 Operator’s Manual 78
- 82 8000 Operator’s Manual 82
- ON R-M PUMP displays 84
- 8000 Operator’s Manual 85 85
- 88 8000 Operator’s Manual 88
- 8000 Operator’s Manual 89 89
- Starting a Program 91
- APP 3/7 Options Screen 93
- 94 8000 Operator’s Manual 94
- Table 2 4 App 3/7 Options 94
- Manual Sample 95
- 96 8000 Operator’s Manual 96
- Automatic Calibration 97
- 1 MANUAL 2 AUTOMATIC 98
- Manual Calibration 99
- Daisy Chaining 102
- 104 8000 Operator’s Manual 104
- 4 Operating the 8000 104
- Agilent Technologies 105
- Preventive Maintenance 106
- Apparatus 3 / 7 107
- Start Immediately 108
- Programmed Clean 108
- Apparatus 1 / 2 111
- Syringe and Seal Replacement 112
- Cleaning the Syringes 113
- Filter Changer (optional) 115
- Report Center Impact Printer 119
- Replacing a Paper Roll 120
- Toggling Your Printer Online 121
- Printer Self Test 121
- Printer Configuration 122
- 124 8000 Operator’s Manual 124
- 8000 Operator’s Manual 125 125
- 126 8000 Operator’s Manual 126
Související produkty a manuály pro Tisk a skenování Agilent Technologies 8000 Series
(82 stránky)© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.045 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce