Agilent Technologies ESG Specifikace Strana 106
- Strana / 302
- Tabulka s obsahem
- ŘEŠENÍ PROBLÉMŮ
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
2-90 Fully Coded 3GPP W-CDMA Personality User’s and Programming Guide
Using Functions ESG Family Signal Generators
3GPP W-CDMA Base Station Performance Testing Option 200
4. Compare the measured BER value in the column titled, “Verification BER Value” with
the limits from the column titled, “Specification Limitations.”
• If the measured value is within the limits, continue to subsection 2.
• If the measured value is outside the limits, determine the cause of failure and repair
the BS. After repair, return to Step 1 of this subsection.
Subsection 2. Dynamic Range Measurement
Complete the following steps to make a dynamic range measurement on your BS.
1. Modify the amplitude level the W-CDMA stimulus.
In accordance with the 3GPP W-CDMA RF specification, increase the amplitude of the
RF output power to
−
91.00 dBm.
On the ESG:
Press
Amplitude >
−
91 > dBm.
2. Introduce the AWGN interferer. This signal acts as an interferer to degrade the BER of
the BS.
On the AWGN signal source:
a. Set the RF output frequency to the same RF output frequency as the ESG.
b. Set the amplitude to
−
73.00 dBm.
c. Set the bandwidth to 3.840 MHz (3.84 Mcps data clock rate).
d. Activate the modulation.
e. Activate the RF output.
3. Measure the BER of the W-CDMA signal in the presence of the AWGN interferer.
The controller or BER test platform measures the BER of the BS in the presence of the
AWGN interferer.
4. Record the BER result in the column titled, “Dynamic Range BER Value” in Table 2-47.
5. Compare the recorded value of the BER result with the allowable values and record the
PASS/FAIL status for the BS.
Example Test Record
Use the following table to record the data from the dynamic range performance test.
Table 2-47 Dynamic Range Performance Test Record
Verification BER
Value
Dynamic Range
BER Value
Specification
Limitations
PASS/FAIL Status
BER ≤0.001
- Agilent Technologies 1
- Contents 10
- ESG Family Signal Generators 11
- Option 200 11
- Overview 12
- Option 200 Overview 13
- Uplink Channel 14
- Overview Option 200 16
- 2 Using Functions 17
- Required Equipment 18
- Configuring the ESG 18
- System Configuration Process 22
- Connect the Equipment 23
- The W-CDMA Configuration 24
- Configure ESG 1 26
- Configure ESG 2 27
- Refer to the following table 28
- Return on both 31
- Channel State 38
- Table 4-12.) 39
- Table 4-12 40
- Amplitude > − 42
- Table 4-12) 46
- In-Band Interferer 59
- Band 1 Interferer 60
- Band 2 Interferer 60
- Band 3 Interferer 60
- CW interferer 70
- interferers I 87
- Interferers BER 89
- Interferers BER Value 89
- Uplink Measurement Setup 92
- Performance Test Preparation 96
- Configuration 104
- Interferer BER 120
- Example Test Record 130
- Troubleshooting 131
- Troubleshooting Option 200 132
- 3 Softkey Reference 133
- # of Blocks 134
- % Power Other ESG 134
- % Power This ESG 134
- Numerics 135
- Actual BER 137
- Actual BLER 137
- Adjust Code Domain Power 138
- All Down 138
- AMR 12.2 (25.944 v3.3) 139
- AMR 12.2 kbps 139
- APCO 25 C4FM 139
- Apply Bit Errors 139
- Apply Channel Setup 141
- BCH Data 142
- Bit Errors (numeric value) 144
- Bit Errors (percent value) 145
- Bits/Frame 146
- Bits Rate 146
- Blk Size 147
- Channel Code 148
- Chip Rate 149
- CRC Size 150
- Create File 151
- Define User FIR 152
- Display FFT 154
- Display Impulse Response 155
- Edit File 157
- Edit Item 157
- Equal Powers 157
- Err Insert 158
- Error Bits 158
- Error Blocks 158
- Ext Clock Rate X1 X2 X4 159
- FBI Pattern 160
- FBI State 160
- Filter Alpha 161
- Filter BbT 162
- Filter Symbols 163
- Frame Clock Interval 164
- Frame Clock Polarity Neg Pos 165
- Gaussian 166
- Generate 167
- Goto Bottom Row 167
- Goto Middle Row 167
- Goto Row 167
- Goto Top Row 167
- Insert 0’s 169
- Insert 1’s 169
- Insert PN9 169
- Interleaver 170
- I/Q Voltage Scale 171
- IS-95 Mod 172
- IS-95 Mod w/EQ 172
- IS-95 w/EQ 172
- Link Control 174
- Link Down Up 174
- Load Default FIR 174
- Load From Selected File 175
- Load/Store 175
- Max Puncture 176
- Num of Blk 178
- Optimize FIR For EVM ACP 180
- Oversample Ratio 181
- Paging Indicator 182
- Physical Channel # 183
- PhyCH Setup 183
- PhyCH Type 183
- Puncture 186
- Rate Match Attr 187
- Ref Measure Setup 188
- Restore Default Filter 188
- RMC 12.2 kbps (25.141 v3.4) 188
- RMC 64 kbps (25.141 v3.4) 189
- RMC 144 kbps (25.141 v3.4) 189
- RMC 384 kbps (25.141 v3.4) 189
- Root Nyquist 190
- Scrambling Code 191
- SecScr Code OS 191
- Select File 192
- Select Pattern 192
- Slot Delay (numeric value) 193
- SFN RST Polarity Neg Pos 193
- Signal Setup 193
- Slot Format 194
- Store To File 195
- Symbol Rate 196
- Sync Trigger Mode Single Cont 197
- TFCI Pattern 198
- TFCI State 198
- Time Offset 198
- Total Bits 199
- Total Blocks 199
- TPC Pat Steps 199
- TPC Pattern 200
- Transport Channel # 201
- TrCH Setup 201
- TrCH State Off On 201
- Tr Position 202
- UDI 64 (25.944 v3.0) 203
- UDI 64 kbps 203
- UDI ISDN (25.944 v3.3) 203
- UE Setup 203
- UN3/4 GSM Gaussian 204
- Uplink Sync Setup 204
- User File 204
- User FIR 205
- Voltage Other ESG 206
- Voltage This ESG 206
- W-CDMA Off On 207
- W Option 200 208
- 4 Operation 209
- W-CDMA Frame Structures 210
- Downlink Data Generation 215
- Couplings and Values 217
- Uplink Data Generation 221
- Capabilities 228
- System Functionality 229
- Uplink Capabilities 235
- Downlink SCPI Commands 242
- CPICH Setup 243
- DCH Transport Channel Setup 244
- DPCH Setup 246
- Filter Setup 250
- OCNS Setup 251
- P–CCPCH Setup 252
- PSCH Setup 255
- SSCH State 255
- Uplink SCPI Commands 256
- DPDCH Channel Setup 260
- Uplink Setup 269
- between downlink and uplink 270
- Programming Example 272
- Uplink Reference Sensitivity 273
- Program Comments 275
- 6 Programming Command 277
- Rectangle 287
- Index I-1 293
- I-2 Index 294
- Index I-3 295
- I-4 Index 296
- Index I-5 297
- I-6 Index 298
- Index I-7 299
- I-8 Index 300
- Index I-9 301
- I-10 Index 302
Související produkty a manuály pro Generátory energie Agilent Technologies ESG
Generátory energie Agilent Technologies EXG Specifikace
(358 stránky)
(358 stránky)
© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.062 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce